Short FinalDOCS
Playing

Departures

From the stand to the edge of your airspace: push-back and taxi, take-off rules, SIDs, climbing out and handing off.

On the ground

With Ground control on (Settings → Realism), departures start on the stand at the apron: “Ground, Easy eight six three, on stand, request push and start, CPT one charlie departure.”

  1. Push and taxi. Select it and press K (or Push back & taxi). It taxis to the holding point of its departure runway.
  2. Holding short. When it arrives it calls “holding short runway two seven left, ready”.
  3. Clear it for take-off (T) when the runway's free.

Landed aircraft roll out, vacate the runway and ask for “taxi to stand”: press K again. Reaching the stand earns +10.

Too much to do? Press U (or the Ground button at the top) to hand pushes and taxiing to the AI ground controller, and again to take it back. With ground control off, departures appear already holding short of the runway.

Left waitingCost
On the stand for more than 4 minutes−50
Holding short of the runway for more than 4 minutes−50
Vacated the runway and waiting more than 100 seconds for taxi−25

Take-off

You can't clear a departure for take-off when:

  • an arrival is established on the same runway within 4 nm (“traffic on short final”);
  • another aircraft is still on the runway (rolling out, or stopped after a rejected take-off);
  • the previous departure from that runway took off less than 45 seconds ago;
  • the runway is closed.

On a single runway that takes both landings and departures (Gatwick, Luton, Harrowfield), every departure needs a gap in the arrivals. Launch it straight after a landing, as the next arrival is still 5 nm or more out.

Departures keep the runway heading until they're through 800 ft, then turn.

Instructions before take-off

While a departure is holding short you can give it a heading (“after departure fly heading…”), an altitude, or a direct to a fix. They take effect once it's airborne, and a heading or direct replaces its SID.

Rejected take-offs

With Runway events on, now and then a departure stops on the runway during its take-off roll (engine warning, bird strike, tyre burst). The runway closes for a minute or two while it's cleared.

SIDs NEW IN 1.11

Every departure has a named departure route (SID), for example CPT 1C, which it mentions when it calls you. Once airborne it flies it by itself:

  1. runway heading until it's through 1,500 ft and 2 nm from the runway;
  2. then a turn straight towards its exit fix;
  3. climbing to 6,000 ft (the SID's stop altitude), or the exit altitude if that's lower.

The radar label and strip show SID CPT 1C. You still need to climb it to its exit altitude (the strip shows it, for example ≥8k) and, with manual handoffs, hand it to centre. Give it a heading and it leaves the SID; give it a direct and it flies that instead. Climbing it doesn't affect the route.

Tip

Departures level at 6,000 ft often ask “request higher”. Climb them within 2 minutes for +10.

Leaving your airspace

A departure is done when it reaches its exit fix at or above the exit altitude. What you get depends on how it left:

How it leftPoints
At its exit fix, at or above the exit altitude (and handed off, with manual handoffs)+100
Near its exit, but below the exit altitude+25
Near its exit, but without a handoff to centre (or the handoff was late)+40
Through the edge of your airspace away from its exit−100

Handing off to centre

With Handoffs set to Manual, you hand each departure to centre yourself. When it's within 14 nm of its exit and at (or climbing to) its exit altitude, a Hand off button appears on its strip. Click it, press A, or type HO. You say “contact centre, good day”, and a few seconds later the pilot calls centre. With handoffs on Automatic this happens by itself.

Short Final documentation. Something wrong or missing? Tell us in the Discord.