Short FinalDOCS
Playing

Giving instructions

Every way to tell a pilot what to do: the panel, the keyboard, clicking the map, typing and speaking.

There's always more than one way to do something. Use whichever suits you; you can mix them freely.

Selecting an aircraft

  • Click it on the radar, or click its flight strip.
  • Tab selects the next aircraft, Shift Tab the previous one.
  • Right-click the radar or press Esc to deselect.
  • Typed and spoken commands can start with a callsign, which selects that plane for you.

The instruction panel

Heading

The − and + buttons turn the aircraft left and right 5° per click (hold Shift for 15°). Click the number to type an exact heading. A faded line on the radar previews the new path. If you prefer, switch to a compass you click to point the aircraft (Settings → Gameplay → Heading control).

Turning an established arrival off its approach cancels the approach.

Altitude

− and + change the target by 1,000 ft. Right-click them (or use Shift ↓/↑) for 500 ft. The lowest you can assign is 2,000 ft and the highest 16,000 ft. Light aircraft fly between 1,500 and 4,500 ft.

Speed

− and + change the speed by 10 kt, from 160 to 280 kt. Below FL100 the limit is 250 kt. NEW IN 1.11 On final you can assign 160–190 kt to hold until 4 miles: see speed control on final.

Send and cancel

By default, heading, altitude and speed changes wait until you press Send (or Enter), so a mis-click never reaches the pilot. Esc cancels them. You can line up a heading, altitude and speed together and send them as one transmission. If you'd rather every click goes out at once, turn off Confirm instructions in Settings → Gameplay.

Buttons

ButtonWhat it does
Cleared ILS 27RClears an arrival for the ILS approach to that runway. One button per landing runway with an ILS.
Other approach…Visual approaches and circling approaches (see Arrivals).
Go aroundSends an arrival on an approach round again.
Contact Tower 1.11Hands an established arrival to Tower.
QNHPasses the pressure setting again, for example to correct a wrong read-back.
Cleared for take-offFor a departure holding short of the runway.
Push back & taxi / Taxi to standGround movements, when ground control is on.
Accept handoffTakes an arrival that centre is offering you.
Hand off to centreSends a departure on to centre near its exit.
Direct to…Sends the aircraft straight to a fix.
Hold hereHolds over its present position.
Expedite climb / descent 1.11Climbs or descends about 60% faster until it reaches its level.
Level off here 1.11Stops the climb or descent at the next 500 ft.
Approve transit / Remain outside / DenyFor VFR light aircraft asking to cross your airspace.

Clicking the map

With an aircraft selected, click a fix on the radar to send it direct to that fix.

Keyboard

The main keys: ← → heading ±5°, ↑ ↓ altitude ±1,000 ft, PgUp PgDn speed ±10 kt, I ILS, T take-off, H hold, G go around, A accept / hand off / Tower, D direct to. The full list, and how to change keys, is in Keyboard shortcuts.

Typing

Press / and type, for example BAW27A L270 A4 S180 then Enter: turn left heading 270, descend to 4,000 ft, speed 180. Leave out the callsign to command the selected plane. Every command is in Typed commands.

Speaking

Hold V (or the 🎙 button) and talk like a controller: “Speedbird 27 alpha, turn left heading 220, descend 4000”. Let go to send. It's recognised offline on your computer. See Voice commands.

Read-backs

Every instruction you give is read back by the pilot over the radio. Listen to them: now and then a pilot reads back the wrong number and flies it. See wrong read-backs. If a pilot says “unable”, the instruction wasn't possible (for example climbing an aircraft with an engine failure) and nothing changed.

Short Final documentation. Something wrong or missing? Tell us in the Discord.